Testing here this morning sending an A1 command via wireless button connected to a W800. I am also using an OmniPro 2 which uses the TW-525 dual phased emulator which Volp sells. The configuration for Homeseer uses a CM11A and W800.īTW what wireless X10 device do you have connected? You can do the same with a wireless to X10 TM751 or RR501 wireless transciever if set for same house code. I use the wireless palm pads to disable TTS while garage door is open if I need to and used to use it to manually controll my irrigation for seasonal turn up or down. Here still using X10 here mostly only for the Christmas lighting. Is this not possible or did I miss something? I was planning to use some of my old X10 controls to activate some of my new HS4 devices. Sending the same command from HS4/X10 device I see this in my logĭevice: X10 Den Fan Lights to On (100) by/from: CAPI Control Handler The plugin works great for sending commands to my X10 devices but if a command is sent from another device (wall button, wireless remote of plugin keypad) I get this in my HS3 log. That's it! You will now find your Sonoff in the Domoticz user interface.HS4, CM11a, Windows 7 with one serial port on the motherboard, x10 since 1990, new to HS The above settings can be defined in user_config_override.h (TBD).cmnd/%topic%/SetOption19 with payload 1 to enable MQTT discovery.Use MQTT or Serial or Web console and execute commands (replace %topic% with the device's unique topic).Each Tasmota device must have its own topic, the easiest way is to set topic to tasmota_%06X (%06X will be replaced by MAC address).Tasmota Configuration ~ Precompiled Binary ~ Set the Ignored device topic to /tasmota/ to avoid unconfigured Tasmota devices from being discovered.Set the Discovery topic to homeassistant unless it has been changed in a custom Tasmota build.Configure the interface with access to your MQTT server ( MQTT Server Address, Port, Username and Password).On the hardware page add Type MQTT Discovery.You have installed the Domoticz MQTT Discovery pluginĬonfigure Domoticz MQTT Discovery plugin. ![]() You have installed/access to a MQTT broker server and made contact with your sonoff.The following services should be made available: Tasmota supports automatic discovery by Domoticz through the Domoticz MQTT Discovery plugin. Toggle the light bulb Tasmota should respond.On the Switches page scroll down and find your Switch as configured in step 1.That's it! You can now control your device from the Domoticz user interface. DzOutTopic with domoticz/out as hardcoded in Domoticz.DzInTopic with domoticz/in as hardcoded in Domoticz.Use the serial interface and execute commands:.cmnd/tasmota/DzIdx1 with payload value read in step 2.i.cmnd/tasmota/DzOutTopic with payload domoticz/out as hardcoded in Domoticz.cmnd/tasmota/DzInTopic with payload domoticz/in as hardcoded in Domoticz.Use MQTT and execute commands (if necessary, replace tasmota with unique topic you configured in Initital Configuration, see point 5 there):.Configure Idx 1 to the value read in step 2.i.Set Out topic to domoticz/out as hardcoded in Domoticz. ![]() Set In topic to domoticz/in as hardcoded in Domoticz.Use the webinterface and select Configuration - Configure Domoticz:.Tasmota provides different ways to configure Domoticz parameters. On the Devices page find the new switch by its name.Make a new virtual switch to be used with Sonoff by clicking Create Virtual Sensors.Make a new virtual switch and remember its Idx number. On the hardware page add Type Dummy (used for virtual switches).Set the Public Topic to flat (which seems to relate to out in the select field).Configure the interface with access to your MQTT server ( Remote Address, Port, Username and Password).On the hardware page add Type MQTT Client Gateway with LAN interface.If not already done configure Domoticz MQTT and Virtual Sensor hardware. ![]() ![]()
0 Comments
Leave a Reply. |